Your shopping cart is currently empty. Please continue shopping.
Werks Adjustable 4-Shoe 33mm XRay XB8 Clutch System (Carbon)
WRX6531
The Werks Racing Power Clutch is a four Carbon shoe design which allows for the maximum possible amount of contact area between the clutch shoes & clutch bell.
This is a Werks Racing Adjustable 4-Shoe 1/8th Scale Off Road Clutch System, with Rulon shoes. This version will work with any 1/8th Scale Off Road Buggy. This clutch system is completely adjustable to allow you to fine tune the performance of the clutch to best match the power characteristics of your engine and the track conditions. The beauty of this system is that you can fine tune the spring tension and adjust the RPM setting that the engine will engage at without changing the clutch.
Just remove the clutch bell and turn the clutch adjusting nut! The tuning features of this clutch are desribed below, however the recommended starting setup is to use the Carbon shoes with gold spring set, and the spring tension nut should be set to 1 turn from flush.
All new packages of the Werks Clutch System now include the externally adjustable nut as part of the package.
Clutch Springs:
The Clutch springs are available in three different tensions. Silver is the hardest, Green is medium and Gold is the softest. You can use the clutch springs to fine tune the RPM that the clutch system will engage at. The stiffer the spring, the later the clutch will engage allowing the engine to spool up to higher RPM's before the clutch will grab. Generally if you have an engine with lots of bottom end, use a softer spring. If you need to get more bottom end snap from your engine, use a stiffer spring.
Clutch Shoes:
The clutch system is available with shoes in three different compounds, which work differently and allow you to fine tune how hard the shoes will grab when they engage. The different compounds are:
Carbon: The Carbon clutch shoes have moderate wear and are a common first choice. They have a linear feel, with a moderate amount of bite and are easy to tune.
Rulon: The Rulon clutch shoes on the other hand usually have higher wear, but the amount of wear is vastly dependent on the amount of slip allowed. They do however have the most grip, but the grip increases with temperature. To properly tune the Rulon shoes you have to be aware of this property, as they will make the engine bog more after about 45 seconds of use (The clutch grabs more so it locks harder). So make sure that you adjust the shoes when the clutch and engine are hot and expect them to slip a little when you first fire up the engine. The Rulon shoes would make an excellent choice of clutch shoe for high traction tracks with an engine with strong bottom end, provided you put in the time to tune them correctly.
Teflon: The Teflon clutch shoes have the least amount of grip but have excellent wear. These shoes are best suited to low traction conditions. Teflon clutch shoes are also beneficial for engines that have less bottom end, as they will allow the engine to spool up and stay in the power band before they grab completely.
Tuning Options:
Due to the 4 shoe design of this clutch system, there are many different tuning variables you can play with to get the ultimate clutch setup. For instance if you like the way the clutch works with the carbon shoes but want a little less slip, you can run 2 carbon shoes and 2 rulon shoes! Or if you want the engine to spool up a bit before the clutch fully grabs, try running 2 carbon shoes and 2 teflon shoes. That way you can avoid using a stiffer spring to get the clutch to grab at higher RPM's, but still allow it to full spool up before it fully engages.
Just remove the clutch bell and turn the clutch adjusting nut! The tuning features of this clutch are desribed below, however the recommended starting setup is to use the Carbon shoes with gold spring set, and the spring tension nut should be set to 1 turn from flush.
All new packages of the Werks Clutch System now include the externally adjustable nut as part of the package.
Clutch Springs:
The Clutch springs are available in three different tensions. Silver is the hardest, Green is medium and Gold is the softest. You can use the clutch springs to fine tune the RPM that the clutch system will engage at. The stiffer the spring, the later the clutch will engage allowing the engine to spool up to higher RPM's before the clutch will grab. Generally if you have an engine with lots of bottom end, use a softer spring. If you need to get more bottom end snap from your engine, use a stiffer spring.
Clutch Shoes:
The clutch system is available with shoes in three different compounds, which work differently and allow you to fine tune how hard the shoes will grab when they engage. The different compounds are:
Carbon: The Carbon clutch shoes have moderate wear and are a common first choice. They have a linear feel, with a moderate amount of bite and are easy to tune.
Rulon: The Rulon clutch shoes on the other hand usually have higher wear, but the amount of wear is vastly dependent on the amount of slip allowed. They do however have the most grip, but the grip increases with temperature. To properly tune the Rulon shoes you have to be aware of this property, as they will make the engine bog more after about 45 seconds of use (The clutch grabs more so it locks harder). So make sure that you adjust the shoes when the clutch and engine are hot and expect them to slip a little when you first fire up the engine. The Rulon shoes would make an excellent choice of clutch shoe for high traction tracks with an engine with strong bottom end, provided you put in the time to tune them correctly.
Teflon: The Teflon clutch shoes have the least amount of grip but have excellent wear. These shoes are best suited to low traction conditions. Teflon clutch shoes are also beneficial for engines that have less bottom end, as they will allow the engine to spool up and stay in the power band before they grab completely.
Tuning Options:
Due to the 4 shoe design of this clutch system, there are many different tuning variables you can play with to get the ultimate clutch setup. For instance if you like the way the clutch works with the carbon shoes but want a little less slip, you can run 2 carbon shoes and 2 rulon shoes! Or if you want the engine to spool up a bit before the clutch fully grabs, try running 2 carbon shoes and 2 teflon shoes. That way you can avoid using a stiffer spring to get the clutch to grab at higher RPM's, but still allow it to full spool up before it fully engages.
